Tuesday, August 5, 2014

Campagnolo Portacatena: A Neat Idea Whose Time Never Came

Back in June when I was doing some research for an article on the wonderful Nivex rear derailleur (see HERE) I found some pictures of the special Nivex dropouts with an integrated chain holder. The way they were designed, a rider could shift the chain from the smallest sprocket to the chain holder, thereby allowing them to remove the rear wheel without touching the chain.

The Nivex dropout with integrated
chain holder -- and special hubs with
semi-axles. Wheel changes were
never easier.
My first thought on seeing the Nivex chain holder was "Wow -- that's just like the Campagnolo Portacatena. I wonder if that's where Campagnolo got the idea?" The evidence seemed to support it. In my research, I had found that it is a generally accepted fact that Tullio Campagnolo saw the Nivex derailleur and the dropouts at the 1949 Salon du Cycle show in Paris, and was impressed enough that he purchased a set. Within a few months, he introduced the first prototype of his Gran Sport parallelogram derailleur which must have been inspired at least in part by the Nivex. Although the Portacatena wasn't introduced until about 28 years later, it seemed not only possible, but highly likely that the idea came from the Nivex chain holder.
The dropout piece of the Portacatena, mounted
on a Campagnolo 1010/B dropout.

Soon after I posted that article, I got my Summer 2014 issue of Jan Heine's Bicycle Quarterly magazine (Vol. 12 No. 4), and wouldn't you know, but there was an extensive article on Tullio Campagnolo: The Visionary Behind the Legend. The article re-examined the myths and legends that surround Mr. Campagnolo and the company that bears his name. And sure enough, short of having Tullio himself rise from his grave and say "yes, that's true," Heine's article lent more credence to what I'd been thinking. As far as giving an explanation as to why Campy waited until 1977 to introduce the chain holder, Heine could only speculate. "Did somebody at Campagnolo find the old Nivex dropouts in a drawer, and think that this could be a good idea?" Nobody knows for sure.

Regardless of who actually came up with the original idea, the Portacatena (literally, "chain-holder") was a neat little item whose time never came.

Anyone who has an 80s vintage frame
with Campagnolo dropouts has probably
seen these little holes. How many knew
what the little holes were for?
The Portacatena consisted of a "C-shaped" aluminum piece (the actual holder) which mounted onto Campagnolo's 1010/B dropouts using two small tapped holes (another version was available that fit into the axle slot of the dropout, for use with bikes that didn't come with the drilled mounting holes). At the control end, the normal shift lever was replaced with a special shift lever that had an extra release button and a 2-position lever stop. When the rider shifted down to the smallest cog, the release button engaged the first stop position and the lever would go no further. When one wanted to shift onto the chain holder, they would press the release button and move the lever to the second stop position which shifted the chain onto the holder. Look, ma' - no greasy hands!

In reading other people's recollections of the Campy Portacatena, I found several references to an interesting benefit that some racers discovered in using it that had nothing to do with wheel removal. When on a long descent, some would reportedly shift onto the chain holder, bypassing the freewheel, and descend swiftly and silently. Sounds like a cool trick, as long as they remembered to shift back on the gears before they had to start pedaling again.

Yes, I have a Portacatena set, still in
 the original package. I just don't
know what bike to mount it on.
So, why didn't the Portacatena catch on? Most likely, it was because in most cases the chain holder essentially took the space of one freewheel cog. In other words, if the frame and hub were spaced for a 6-speed cluster (typically 126 mm), one would normally have to use a 5-speed freewheel in order to use the Portacatena -- though I imagine one could maybe get away with an Ultra 6 (narrow-spaced) freewheel. I'm sure 7 speeds (or more) would be out of the question. At a time when the industry was adding (and consumers apparently demanding) more and more cogs, Campagnolo was essentially asking riders to go the other direction. Many riders who even knew of the existence of the chain holder probably didn't think it was worthwhile.

As regular readers might guess, I have a Portacatena set, still in the original packaging. I only just opened it today so I could put the instruction pamphlet onto my scanner (see below). I've had it for years now -- purchased mainly as in interesting curiosity, thinking I might install it on a bike some day if the right bike presented itself. So far, it simply remains an interesting curiosity. I thought about putting it on my Masi, which has the right dropouts, but I've never gotten around to it.

Here are scans of the instruction pamphlet:


Notice that the instructions show the Portacatena in use with a 6-speed freewheel. They don't mention anything about the necessary spacing to make that work. Hmmm. . .
I have seen the devices used with 6-speed freewheels -- as mentioned, it seems that an Ultra-6 would probably work, as it is supposed to fit into the space of a 5-speed. To use a normal-spaced 6, I suppose one could re-space the hub to gain more room on the drive side, but that would also increase wheel dish and increase the possibility of a bent axle. There's one pictured on Classic Lightweights UK that may have been done this way. The description in the picture there says it uses a 6-speed freewheel with 7-speed axle and frame spacing. But unless I'm mistaken, both 6 and 7-speed systems used the same 126 mm frame and axle spacing, so I'm guessing the wheel in that case has some extra dish.

The Portacatena was quietly dropped from the Campy catalogs some time in the early 80s (I couldn't find it in the '84 catalog), though according to framebuilder and blogger Dave Moulton, Campagnolo continued making the dropouts with the mounting holes well into the 90s (see HERE) -- either that, or they made a ton of them in the early 80s and it took years to get through the stock. Since the introduction of the Portacatena in 1977, we've seen the industry go from 6 to 7, then 8, and eventually all the way up to 11 speeds. The real estate between a bicycle's dropouts has become pretty crowded these days, so I don't imagine anyone bringing back this nifty little item. But for retrogrouches and vintage bike lovers, it can be cool piece of useful nostalgia.

11 comments:

  1. I've never seen one of those before, thanks for the education. I've always thought the little peg braze-on for hanging a chain on was a novel idea, and now I see this. In the 70's I wasn't near anything nice enough to warrant Campy bits, though. (Scooters and a banana seat Schwinn, all the way!)

    I've seen Campy dropouts with holes in them, but I always figured some shade-tree bike mech was just rigging something up for fenders or racks or something.


    Wolf

    ReplyDelete
  2. Very interesting! A pic with the chain in place would be handy if one could be found. I suspect you are right - the value of the device was outweighed by the value of an extra cog. I see there is a current device that "catches" a chain at the RD end - the Quikchanger (available as a clamp-on or brazed on)

    http://www.columbinecycle.com/other_products.php

    Maybe the Portacatena can be resurrected? But the fact you have one - unfitted - plus a matching bike, speaks to its value

    ReplyDelete
  3. I recently installed one on a friends bike. No good reason for it, just seemed cool to do it now.

    ReplyDelete
  4. I just picked up one from a cycle jumble for the princely sum of 50p. Though it only has one screw fixing in the centre and a mount to fir from the inside of the dropout rather than the 2 portecatena holes. I'm guessing this is a later version though I've never seen one before.

    ReplyDelete
    Replies
    1. There was a version made that was designed to attach to bikes that didn't have the two mounting holes in the dropout. That must be the one you have.

      Delete
  5. Hey bike people! Anybody got specs on the two little screws that mount the portacatena to the dropout? I have the portacatena but not the two little screws. Campy doesn't provide a part number or specs for these little beauties. Outside diameter and thread pitch (or the screws themselves) would be most helpful for this fellow old bike guy. Thanks

    ReplyDelete
  6. Hi, I have the portacatena but not the shifter. Can I just move the change over by hand temporarily to remove the rear wheel? Anyone has a shifter they like to sell as reasonable price? :)

    ReplyDelete
    Replies
    1. I have the shifter but not the Portacatena. Not sure if I want to sell though. It's such a unique piece. Price? I have no idea. But I've never seen another one, nor even heard of it before. Had no idea what it was. Thanks Retrogrouch!

      Delete
  7. I have one of those portacatenas on the bike I bought in 1980. It was matched with a Regina 6 speed freewheel, when 6 speeds was the norm back then. It worked beautifully until the axel broke and I had to find a replacement. It was a little shorter and the chain hanger never fit properly again.

    ReplyDelete
  8. I purchased a portacatena on e-bay, still in the original packaging. It came with the screws and the shift lever. I’ve installed it on my ‘78 Raleigh Team Pro (126mm). I’m using a suntour ultra six so I did not have to give up a cog. The spacing is tight and even varies slightly from on 126mm wheel to another. It is a temperamental little piece of machinery. The shift lever cannot be pushed too hard or you will shift past the stop in 0 gear. It is best to place your index finger beneath the stop when shifting into the smaller cogs to avoid a mid-shift. Shifting from 0 to 6 cog when you put the wheel back on cannot be done from a complete stop or you risk binding the chain on the bottom of the seat stay. I haven’t figured out how to completely avoid getting my hands greasy removing and re-installing the rear wheel yet, although it definitely helps. All in all I can see why it was discontinued. I’m leaving mine on though, because it’s cool.

    ReplyDelete
  9. I have 2 Portacatena set ups on 2 different bikes, both of them use the bolt through the dropout slot to secure them. It shifts you rear axles forward in the dropout as a result. One is on my Merckx with a Regina 5 speed CX / CXS which works perfectly with it. The other on my Masi with an ultra 7 cluster will not let you shift to the lowest gear without rubbing against the Portacatena, when I installed I did not know about the losing the 1 gear space rule, so my Masi doesn't hang the chain right and some times needs help. Because the freewheel moves forward, it affect my Campi Rally ( 1st gen ) derailer getting onto my 28t bail out gear. I used a Wolftooth Roadlink to lower the Rally centerline to get better chain wrap on the big gear with mixed results. I'll probably pull the Portacatena on my Masi.

    ReplyDelete